View the full Swivel Catalogue
A coupling that disconnects and a joint that rotates solve different problems on a drilling spread. Put them into the same purchase order and another question becomes essential: what can the complete line actually handle?
Fox Global is sending 3-inch Fig 200 hammer unions and 3-inch Series 20 low-pressure 600 psi swivels to a drilling contractor in Queensland. This dispatch provides a useful starting point for examining connection selection, movement, pressure limits and maintenance planning.
The order combines two familiar names, but they should not be treated as one interchangeable product. A hammer union provides a demountable connection. A swivel provides controlled rotation. Neither replaces a properly supported pipe layout, suitable hose assembly or application review.
For engineers and procurement teams, the practical task is to establish how each component fits the service. For operators, it is to recognise what the assembled system permits before pressure is applied.
Open the job file: two components, two responsibilities
The confirmed dispatch details are straightforward: 3-inch Fig 200 hammer unions, 3-inch Series 20 swivels, a specified swivel rating of 600 psi, and a Queensland drilling contractor destination.
Fluid composition, operating temperature, union end connections and the exact swivel part number are application details to verify against the order and manufacturer documentation. They should never be guessed from a product photograph.
| Selection point | Fig 200 hammer union | Series 20 / Style 20 swivel |
|---|---|---|
| Main purpose | Connect and disconnect compatible line sections | Allow rotation about the joint axis |
| Size for this dispatch | 3-inch nominal | 3-inch nominal |
| Pressure reference | Fig 200 commonly denotes 2,000 psi cold working pressure; verify the supplied product | 600 psi specified for this dispatch |
| Movement once assembled | Union connection remains fixed during operation | Controlled swivel movement within approved duty |
| Connection details | Confirm pipe-thread or weld-end arrangement | Confirm thread type, gender and dimensions |
| Information needed before installation | Matching halves, figure, size, condition and service suitability | Part number, rating, materials, seals and permitted movement |
Manufacturer literature distinguishes the 600 psi threaded low-pressure swivel family from other material and pressure families. It also identifies Fig 200 as a 2,000 psi cold working pressure union category. Those are separate specifications, not a combined assembly rating. technipfmc.com technipfmc.com
Read “Series 20” alongside the manufacturer’s description
Customers may enquire about a “Series 20 Chiksan swivel”, while a manufacturer catalogue may describe the configuration as “Style 20”. The part number and drawing should resolve the terminology.
Style 20 generally identifies a straight-through swivel arrangement. It does not, by itself, establish pressure capacity, connection type, sealing material or suitability for a particular fluid.
Chiksan® is a manufacturer trade name. When genuine branded equipment is required, specify that requirement explicitly. A visually similar industrial swivel should not be represented as the same product without supporting identification.
The pressure decision comes before the connection decision
The most consequential purchasing mistake is to see “Fig 200” and assume every connected component can work at 2,000 psi.
A 600 psi swivel remains a 600 psi component when fitted beside a higher-rated union. The allowable working conditions of the finished assembly depend on every pressure-containing item, including hoses, adapters, valves, seals and pipework.
The assembly cannot exceed the lowest applicable component rating, and temperature, fluid compatibility or installation conditions may reduce the allowable duty further.
Put the units on the enquiry
For comparison:
- 600 psi is approximately 41.4 bar or 4.14 MPa.
- 2,000 psi is approximately 137.9 bar or 13.79 MPa.
“Low pressure” describes a product category relative to higher-pressure oilfield equipment. It does not mean low consequence. A pressurised three-inch line still requires controlled isolation, competent installation and suitable protection.
Cold working pressure is also different from proof-test pressure or burst pressure. A successful pressure test does not authorise a higher operating rating.
A Queensland pumping example
Consider an illustrative water-transfer circuit operating at 300 psi with a 600 psi swivel. The normal gauge reading alone does not settle the selection.
The engineering review should also consider maximum pump capability, blocked discharge conditions, relief settings, rapid valve closure and pressure spikes. If credible operating events exceed a component’s permitted conditions, the system needs appropriate protection or different equipment.
This example is not the confirmed duty of the Queensland order. It demonstrates why Fox Global asks for maximum service conditions rather than selecting solely from normal running pressure.
Discuss your pressure envelope with Fox Global on 1300 852 795 or email sales@foxglobal.com.au. Providing the pump details and fluid information helps the team assess the enquiry efficiently.
Decide what needs to move—and what needs to disconnect
Hammer unions and swivels are often ordered together because a temporary line may need both convenient separation and controlled orientation.
That does not make their functions interchangeable.
When a hammer union earns its place
A Fig 200 hammer union allows compatible sections to be connected through a union assembly without rotating an entire pipe string. This can be useful where equipment is repeatedly assembled, removed or reconfigured.
The connection still needs adequate access, compatible mating parts and sound sealing surfaces. A union crowded against a skid frame may be difficult to assemble correctly or inspect.
The union should be treated as a complete connection system. Confirm the nut and both mating subs belong to an approved combination. Nominal size, paint colour or apparent thread engagement are not sufficient evidence of compatibility.
When a straight swivel is useful
A Style 20 swivel can provide axial rotational freedom in a suitable fluid line. In an approved arrangement, that movement may help manage orientation and reduce the tendency to twist adjoining components.
It is not a universal joint. A straight swivel does not automatically accommodate lateral displacement, an incorrect centreline or an unsupported hose hanging from the connection.
If the layout requires movement in several directions, additional geometry or a different assembly may be necessary. That decision should follow the required movement envelope and load assessment.
Continuous drill rotation is a separate duty
A conventional industrial swivel should not be selected as a drill-string rotary water swivel simply because both products rotate.
Manufacturer guidance distinguishes permitted swivel movement from continuous rotary service. Continuous speed, duty cycle, seal heating and mechanical loading require a product specifically approved for that duty. technipfmc.com
Likewise, controlled rotation is not proof of vibration isolation. A swivel may alter how a line accommodates movement, but it does not automatically absorb pump pulsation or eliminate fatigue.
Follow the fluid through the proposed layout
A useful design review starts at the pump and follows the fluid to its destination. At each change in section, identify the bore, connection, material, support and possible wear mechanism.
This reveals problems that a list of component ratings can miss.
Nominal three-inch size is not a measured bore
Three-inch industrial pipework is commonly associated with DN80 nominal sizing. That designation does not mean every fitting has an 80 mm internal diameter.
Pipe schedule, thread geometry, sealing profiles and adapters can change the available flow area. The actual minimum bore matters when estimating velocity, pressure loss and passage of suspended material.
For an illustrative calculation using a genuine 76.2 mm internal bore:
| Flow rate | Approximate average velocity |
|---|---|
| 300 L/min | 1.10 m/s |
| 600 L/min | 2.19 m/s |
| 900 L/min | 3.29 m/s |
These values use velocity = volumetric flow ÷ cross-sectional area. They are calculation examples, not approved flow limits or confirmed bores for the supplied products.
Small restrictions can become large operational issues
A reducer, sharp internal transition or partially obstructed fitting can influence system performance even when the main hose is correctly sized.
For water service, restrictions may contribute to avoidable pressure loss. With suspended solids, local velocity changes may also influence wear or settlement.
For drilling fluids, assess viscosity, solids loading, particle characteristics and cleaning requirements. A fitting suitable for clean water is not automatically appropriate for abrasive mud.
Pressure rating alone does not answer those questions. Request material and service confirmation before treating a general-purpose swivel as a slurry-handling component.
Consider the return line as well as the delivery line
A delivery circuit and a return circuit may have different pressure conditions, fluid properties and contamination levels.
A nominally low-pressure return can still become pressurised through blockage or valve operation. Conversely, a suction line may experience vacuum conditions that are not established by a positive-pressure rating.
Confirm both duties explicitly. Do not assume “600 psi” establishes vacuum capability, gas suitability or resistance to external pressure.
Resolve the interfaces before the freight leaves
A connection error discovered at the workshop is inconvenient. The same error discovered on a remote Queensland drilling site can delay commissioning and trigger urgent replacement freight.
The best prevention is a clear interface schedule.
| Interface detail | What to record | What it prevents |
|---|---|---|
| Thread standard | NPT, BSPT or other specified form | Ordering superficially similar threads |
| Thread gender | Male or female at each end | An adapter mismatch |
| Union identity | Size, figure, manufacturer and approved combination | Unverified mating of components |
| Weld preparation | Pipe material, schedule and end preparation | Incorrect fit-up or unsuitable welding |
| Installed dimensions | Length, clearance and support positions | A component that cannot fit the space |
| Service conditions | Fluid, temperature, pressure and movement | A mechanically fitting but unsuitable product |
NPT and BSP threads are not interchangeable merely because a connection starts to engage. Confirm markings and dimensions using suitable inspection methods.
If weld-end components are specified, fabrication needs an appropriate procedure, competent personnel and inspection requirements suited to the installation. Do not weld or modify a swivel body without explicit manufacturer approval.
Materials and seals need their own review
The catalogue construction of one product family should not be applied to every swivel carrying the same style number.
Record the actual body material, wetted components, seal specification and any coating requirements for the supplied part. Where traceability or material certificates are required, nominate them before ordering.
Seal compatibility depends on the complete fluid composition and operating temperature. Diesel contamination, cleaning agents or treatment chemicals can matter even when the main service is described as “water”.
External corrosion also deserves attention. Coastal storage, wet transport and unprotected threads may affect equipment before it reaches service.
A short selection meeting can prevent a long replacement exercise
For a drilling contractor, procurement quality is more than obtaining the correct diameter at a competitive price.
A useful enquiry allows the supplier to identify uncertainty before the order is placed.
Send Fox Global the following:
- Quantity and required delivery date.
- Property, depot or site delivery location and receiving contact.
- Existing part numbers, markings and clear photographs.
- Fluid composition, including solids and additives.
- Normal and maximum pressure, temperature and flow.
- End connections, pipe schedule and available installation space.
- Required movement, frequency and whether operation involves continuous rotation.
- Documentation, testing, spare-parts and identification requirements.
If some information is unavailable, identify the gap. A clear uncertainty is easier to resolve than a confident but incorrect assumption.
Compare the full cost of supply
Unit price is only one procurement measure. Consider whether the quotation identifies the manufacturer, service limitations, connection details and expected lead time.
Also consider the consequences of receiving an unsuitable component: return freight, lost mobilisation time, workshop rework and additional administrative effort.
A spare item can be valuable on a remote job, but only when it is the correct item. An unlabelled “similar” swivel stored in a toolbox is not an effective contingency plan.
Ask about suitable seal kits and replacement parts when placing the original enquiry. Parts availability and interchangeability should be confirmed against the exact model.
Handover from stores to installation
Receiving inspection is the point where the purchase order becomes physical equipment.
Check quantities and identification before components are mixed with existing stock. Retain labels and certificates with the relevant asset record.
Look for transport damage, thread damage, corrosion, contamination and missing protective caps. Quarantine anything with unclear identification or a condition concern.
For the swivel, assess condition and movement only as permitted by the manufacturer. Smooth movement in an unloaded joint is not a substitute for a pressure-integrity assessment.
Keep the load off the connection
Pipe weight, hose weight and operator handling can impose bending loads on a joint.
Support the line so that the swivel does not become the sole structural support for an adjoining assembly. Allow suitable hose bend radius and avoid a layout that requires the hose to pull the fitting into alignment.
A component can be within its internal-pressure rating and still be subjected to unacceptable external loading. Pressure selection and mechanical layout must therefore be reviewed together.
Establish a controlled commissioning method
Before introducing pressure, confirm assembly, support, connection compatibility and required documentation.
Use a commissioning procedure appropriate to the equipment and site. It should address the test medium, controlled pressure increase, exclusion arrangements, leak observation and acceptance criteria.
Do not adopt a generic pressure multiplier from an unrelated component. The approved test conditions must account for the complete assembly.
Never search for a pressurised leak with a hand or attempt to correct leakage by striking or tightening a live union.
Plan maintenance around evidence
A fixed maintenance interval copied from another operation can be misleading. Operating hours, movement frequency, contamination and exposure may differ substantially.
Use manufacturer instructions as the starting point, then build the inspection programme around the actual service and recorded condition.
Before use
Look for leaks, damaged union wings, body damage, corrosion, displaced supports and evidence that adjoining hose has twisted.
Check that identification remains readable. A rating that can no longer be verified creates a selection problem as well as a maintenance problem.
Report changes in operating behaviour. A joint that becomes stiff, noisy or loose should not be treated as normal simply because fluid still passes through it.
During planned shutdowns
Isolate the equipment, prevent restart, release trapped pressure and verify the safe state before inspection or disassembly. Consider sections trapped between closed valves and any fluid or gas that can remain stored. Australian plant-isolation guidance specifically addresses stopping plant, locking out energy sources and dissipating stored energy before work. SafeWork SA
Use the specified lubricant, where lubrication is required, and follow the manufacturer’s method. Adding grease indiscriminately does not repair worn bearings, damaged seals or an eroded body.
Inspect sealing surfaces and replace approved service parts where appropriate. Damage to a pressure-containing body requires assessment; a new seal does not restore lost wall thickness.
After repair or replacement
Record the work, parts used, inspection outcome and required verification.
Keep maintenance history with the equipment identification. This helps distinguish an isolated seal issue from a recurring problem caused by loading, contamination or unsuitable duty.
Protect cleaned components during storage. Cap openings, keep mating surfaces clean and segregate quarantined items from serviceable stock.
Read the symptom before ordering the spare
The following troubleshooting guide supports fault investigation. It does not authorise continued operation or live adjustment.
| Observation | Possible contributors | Appropriate next step |
|---|---|---|
| Leakage at the union | Damaged seating surface, contamination or incorrect mating parts | Isolate, depressurise and inspect the complete connection |
| Leakage at the swivel | Seal wear, incompatibility, scoring or excessive loading | Remove from service for model-specific assessment |
| Stiff or uneven movement | Contamination, bearing damage, corrosion or misalignment | Check installation and internal condition under approved procedures |
| Repeated short seal life | Wrong seal material, temperature, solids or unsuitable duty | Review service conditions before another rebuild |
| Excessive movement or play | Bearing or retention wear, damage or loading issues | Quarantine and obtain a competent assessment |
| Hose twisting remains | Wrong swivel location, restricted movement or incorrect layout | Review orientation, supports and required motion |
| Rapid external corrosion | Exposure, damaged protection or unsuitable storage | Assess condition and improve protection or material selection |
The recurring fault is often more informative than the failed part. Three consecutive seal replacements may point towards an unresolved application issue rather than three unrelated seal defects.
For help identifying replacement components or reviewing an existing arrangement, call 1300 852 795 or send photographs and operating details to sales@foxglobal.com.au.
Separate useful advantages from unsuitable expectations
The value of these components depends on applying each one within its limits.
A hammer union may make repeated line separation more practical. A correctly selected swivel may help manage rotational orientation. Together, they can support a serviceable layout without assigning every movement task to the hose.
However, neither component guarantees a longer service life on its own. Installation, fluid conditions, pressure events and maintenance remain decisive.
| Requirement | Useful equipment approach | Limitation to resolve |
|---|---|---|
| Frequent line disconnection | Compatible hammer union | Isolation, access and seating condition |
| Axial orientation adjustment | Approved straight swivel | Permitted movement and external loads |
| Multi-directional movement | Engineered hose or articulated arrangement | Bend radius, geometry and support |
| Continuous drill-head rotation | Purpose-designed rotary swivel | Speed, seals, duty cycle and loading |
| Abrasive fluid transfer | Components assessed for the actual solids duty | Erosion allowance and inspection strategy |
A flexible hose also requires its own specification. Hose construction, working pressure, temperature limits, chemical compatibility and end fittings should be selected as an assembly.
The correct answer may be a coordinated package rather than a single replacement fitting.
Australian applications: use the same questions, not the same product
The Queensland dispatch concerns drilling, but the selection method is relevant across many industries.
A regional bore-drilling operation might prioritise serviceability and transport protection. A civil pumping contractor in Brisbane may need a layout that can be assembled repeatedly within a restricted footprint.
A mine maintenance team near Mackay may place greater emphasis on identification, spares and shutdown access. These are representative Australian scenarios, not additional claims about the destination or performance of this order.
Fox Global’s experience extends across mining, civil construction, food and beverage, chemical processing, water treatment, manufacturing, agriculture, oil and gas, marine and waste management.
That broad experience helps the team ask useful application questions. It does not mean the same 600 psi swivel is suitable for every sector.
For food and beverage production, hygienic design and cleanability may lead to a different product family. Chemical processing requires careful assessment of wetted materials and seals. Marine service introduces corrosion and environmental exposure considerations.
Waste management may involve solids, contamination and cleaning duties. Oil and gas requirements can include specialised service classifications that cannot be inferred from a general-purpose pressure rating.
Three avoidable mistakes at the stores counter
The last few minutes before an item is issued can determine whether the installation team receives usable information or another identification exercise.
Mistake: combining serviceable parts with unidentified leftovers. A workshop may have several union halves that appear similar. Keep matched components together and retain their identification. A collection of loose nuts and subs should not become an assembly simply because the pieces seem to fit.
Mistake: using the swivel to recover an installation error. If the line needs to be forced into position, stop and examine the layout. A swivel can permit defined rotation, but it cannot make an incorrect pipe length, poor support position or misaligned connection acceptable.
Mistake: ordering the replacement without describing the failure. “Send another three-inch swivel” leaves important questions unanswered. Record where the leak occurred, whether movement became restricted, what fluid was present and whether operating conditions changed. This helps the supplier identify the component and supports a more useful technical review.
Make the receiving record useful six months later
A simple equipment record should connect the purchase order, manufacturer part number, delivery date and installed location. Include clear photographs of markings before they become obscured by dirt or paint.
Where the site uses asset numbers, apply identification through an approved method that does not damage the pressure boundary or interfere with operation. Retain the relevant instructions and inspection requirements with that record.
For a contractor moving between Queensland projects, this information helps the next crew understand what has arrived. It also makes a future spare-parts enquiry more precise.
The benefit is practical: fewer assumptions, clearer maintenance decisions and a better chance of identifying the correct replacement on the first enquiry. Good records also help procurement distinguish a genuine repeat requirement from a different component that happens to share the same nominal size.
Practical answers for the purchasing desk
Is a Fig 200 union rated to 200 psi?
The figure number is a product classification, not a direct statement of 200 psi. Fig 200 commonly refers to a 2,000 psi cold working pressure category. Confirm the actual manufacturer rating, size and service conditions.
Does a 2,000 psi union make the swivel assembly suitable for 2,000 psi?
No. A 600 psi swivel remains a limiting component. Another item or service condition may reduce the permissible assembly duty further.
Are Series 20 and Style 20 always identical?
Treat the names as enquiry terminology until the manufacturer and part number are established. Confirm the configuration on the drawing rather than assuming equivalence from the number alone.
Can a swivel be rotated while pressurised?
Some products permit controlled rotation under specified conditions. That does not establish continuous-rotation suitability or authorise manual adjustment near a live pressure system. Follow the exact product instructions and site procedure.
Can the supplied swivel handle drilling mud?
That requires confirmation of the fluid, solids, additives, temperature and operating duty. A drilling contractor destination is not evidence that every supplied component is approved for abrasive mud.
Do Fig 200 unions from different manufacturers interchange?
Do not assume so. Obtain confirmation of the complete approved mating combination. Similar dimensions or partial engagement are insufficient.
Are the connections NPT?
The specific order and part number must establish the connection. Nominal size and style do not prove the thread form. Confirm NPT, BSP or another connection before supply.
How often should seals be changed?
Use manufacturer guidance and actual condition, service hours and operating severity. Avoid assigning a universal interval to equipment with different fluids and movement duties.
Can Fox Global assist outside Queensland?
Yes. Fox Global supports enquiries and supply across Sydney, Melbourne, Brisbane, Perth, Adelaide and regional Australia. Confirm availability, documentation and freight arrangements for the particular requirement.
Finish the purchase with an installation-ready brief
Fox Global is a proudly Australian-owned and family-operated business supplying industrial hose, valves, fittings and fluid-transfer components.
For this Queensland drilling dispatch, the useful conversation extends beyond “three-inch fittings”. It includes what disconnects, what rotates, what contains pressure and what must be checked before installation.
Customers can draw on responsive communication, technical product knowledge, custom hose and fitting solutions, and national supply capability. Where an enquiry needs manufacturer clarification, resolving that detail forms part of selecting the right package.
For a workshop in Sydney, a maintenance team in Melbourne, a Brisbane drilling depot, a Perth resources project or an Adelaide industrial facility, the same principle applies: specify the complete duty and make the interfaces clear.
Send your component list, photographs and required delivery date to sales@foxglobal.com.au, or call 1300 852 795. Fox Global can help turn the enquiry into a defined supply requirement, with the ratings, connections and supporting information agreed before dispatch.



